Seagull Models SPORT CRUISER Especificações

“Graphics and specifications may change without notice”.MS:148ASSEMBLY MANUALSpecifications:Wing span ------------------------------70.9in (180cm).Win

SPORT CRUISER. Instruction Manual.10 2) Follow diagram below for wheel pantinstallation: 1) Assemble and mounting the landinggear ,wheels to the

11www.seagullmodels.comC/A glue.Landing Gear.wheel Pant.Locker glue.1) The blind nuts for securing the landinggear are already mounted inside the fu

SPORT CRUISER. Instruction Manual.12LANDING GEAR INSTALLATION:A. NOSE GEAR:1234586735) Slide the pushrod tube in the firewall andguide it through th

13www.seagullmodels.com2mm.4mm.8448456767M3x6mm.

SPORT CRUISER. Instruction Manual.14Trim and cut.COWLING.Trim and cut. 1)Slide the fiberglass cowl over the engineand line up the back edge of the co

15www.seagullmodels.com 3) Install the muffler and muffler extensiononto the engine and make the cutout in thecowl for muffler clearance. Connect t

SPORT CRUISER. Instruction Manual.16Balsa stick.Electric motor.Battery.4) Locate the plywood battery tray to thefuselage. Tighten the screws using ma

17www.seagullmodels.comINSTALLING THE SPINNER. Install the spinner backplate, propeller andspinner cone.The propeller should not touch any partof th

SPORT CRUISER. Instruction Manual.188) A string has been provided in the wing topull the aileron lead through to the wing root.Remove the string from

19www.seagullmodels.com9) Set the aileron hatch in place and use aPhillips screw driver to install it with four woodscrews.AILERON PUSHROD HORN INSTA

SPORT CRUISER. Instruction Manual.2INTRODUCTION.Thank you for choosing the SPORT CRUISER ARTF by SEAGULL MODELS COMPANY LTD. TheSPORT CRUISER was de

SPORT CRUISER. Instruction Manual.20INSTALLING THE HORIZONTAL STABILIZER.1) Using a ruler and a pen, locate thecenterline of the horizontal stabilize

21www.seagullmodels.comINSTALLING VERITICAL FIN. 1) Using a modeling knife, remove thecovering from over the precut hinge slot cutinto the lower rear

SPORT CRUISER. Instruction Manual.22RUDDER PUSHROD HORNINSTALLATION.Rudder control horn.Control horn.M2 lock nut.Metal clevis.Rudder pushrod.Rudder pu

23www.seagullmodels.comINSTALLATION PILOT AND CANOPY.1) Locate items necessary to install pilot, andcanopy.2132) A scale pilot is included with this

SPORT CRUISER. Instruction Manual.24Wing bolt.Receiver.Battery.ATTACHMENT WING-FUSELAGE.Wing tube. Attach the aluminium tube into fuselage.INSTALLIN

25www.seagullmodels.comBALANCING.  1) It is critical that your airplane bebalanced correctly. Improper balance willcause your plane to lose control

SPORT CRUISER. Instruction Manual.26 We wish you many safe and enjoyableflights with your SPORT CRUISER. 7) Check the receiver antenna. It shou

3www.seagullmodels.comADDITIONAL ITEMS REQUIRED. 0.75- 0.95 2-stroke. 0.91 - 1.25 4-stroke. Comput

SPORT CRUISER. Instruction Manual.4The control surfaces, including theailerons, elevators, and rudder, areprehinged with hinges installed, butthe hing

5www.seagullmodels.com 4) Deflect the aileron and completelysaturate each hinge with thin C/A glue. Theailerons front surface should lightly contact

SPORT CRUISER. Instruction Manual.63mm.EpoxyAileron control horn.HINGING THE ELEVATOR. Glue the rudder hinges in place using thesame techniques use

7www.seagullmodels.comINSTALL ELEVATOR CONTROLHORN.EpoxyEpoxyAileron control horn.INSTALL RUDDER CONTROL HORN.Epoxy.Repeat steps to install the rudde

SPORT CRUISER. Instruction Manual.8 3) Carefully bend the second nylon tubeup at a 45º angle. This tube is the vent tube. 4) Test fit the stopper a

9www.seagullmodels.comBlow through one of the lines to en-sure the fuel lines have not become kinkedinside the fuel tank compartment. Airshould flow